Internal: 300w x 150d x 150h mm
Water level maximum: 130mmshelf fitted working depth 115mm
Packed: 38 x 23 x 29 cm
Comprising of a high quality corrosion resistant stainless steel tank, with a bright clean finish housed in a durable paint finished outer case. Painted surfaces feature anti-bacterial finish with good chemical resistance. Fitted with side lifting handles for ease of transportation.
Heaters and temperature sensor concealed under the tank providing a clutter free working area easy to wipe clean.
Supplied with a removable sturdy low height stainless steel perforated shelf, for even heat distribution. The shelf provides a deeper volume of water, for standing containers and accessory test tube racks in the bath.
Temperatures can be easily and rapidly set with the push button, wipe clean control panel.
Temperature setting is retained in memory, even after ‘power off’.
Illuminated on/off switch and heater indication lamp.
We verify the performance of every bath calibrating its controls and water temperature for consistent temperature control in use.
IP rated clear booted on/off mains switch.
Bath fitted with nonslip rubber feet.
Covering the bath with a lid reduces energy consumption and running costs.
This range of baths is not designed for boiling, the NE1B Boiling Bath range is recommended.
The lower the figure, the less energy used. Information supplied for size and range comparison, guidance only and measured consumption at set point. Please remember that the energy consumption may vary due to factors such as its location, ventilation, ambient temperatures and loading.
2. The shelf in the stainless steel tank provides a stable support for flasks/bottles/racks that can be removed for cleaning. The shelf is a low height design maximizing the working height in the bath, either needing less water when compared with traditional water baths or allowing tall containers or vessels to be immersed to a greater working depth. With lower water levels comes the benefit reduced heat up times and energy saving.
3. Three-year warranty and comprehensive customer support.
4. Broad range of accessories available to suit wide range of applications.
5. Before leaving our factory every water bath is identified with a unique serial number and undergoes a factory calibration adjusting control to known traceable value, electrically tested for safety at final inspection and a test certificate enclosed in rear of the instruction book.
6. Painted surfaces feature “anti-bacterial technology” which inhibits bacterial growth, improving hygiene requirements as demanded by clinical and laboratory environments. The Clifton range features easy to clean surfaces and finishes that are resistant to routine and efficient disinfections. The efficacy of the finish is maintained over time, as the anti-bacterial agent is integral within the paint finish.
Flat One Piece Stainless Steel Lid for 2 and 4 Litre Baths
Stainless steel flat lid minimizing heat loss, saving energy, and assisting to maintain bath temperature. Also when a Clifton water bath is 'not in use', with this lid fitted it prevents contamination of liquid from airbourne particles acts as a dust cover. The lid is fitted with an insulated handle.
Lift Off Gable Lid to suit 2 and 4 litre Unstirred Baths
Clifton® clear polycarbonate Gable Lids helps reduce evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These clear plastic gable lids with a high profile allows extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use
Stainless Steel Gable Lid to fit 2 and 4 Litre Unstirred Baths
Clifton® Stainless steel Gable Lids helps reduce evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These stainless steel gable lids with a high profile allows extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use
Hinged Gable Lid to suit 2 and 4 Litre Unstirred Baths
Using conventional lift off lids when removed from a water bath, condensation runs all over your bench top, a mess to clean up. Where do you put the lid once removed?
Hinged lids have a number of benefits in use over lift off lids. They simply hinge open 90° and stay open and any condensation collects in the lid, samples/work can be easily removed or placed in water bath. Close the lid and all the collected condensation runs into rear of the water bath. No mess. The hinge lid can be removed easily and quickly for cleaning or access.
2 x 114mm Stainless Steel Concentric Ringed Lid to suit 4 Litre Unstirred Baths
The lid and rings are manufactured from stainless steel. The concentric rings provide varying hole diameters in the lid. In use the lid minimises evaporation and maintains temperature stability of the water bath when tall vessels are being heated at elevated temperatures.
Stainless Steel Wire Basket for 4 Litre Baths
Stainless steel. Baskets recommended for use with Ultrasonic baths.
Polypropylene Spheres
This blanket of hollow spheres is ideal for open tanks of water. Reduces thermal losses - Savings of up to 75% can be achieved with a single layer - Increase energy saving & reducing costs. A single layer of spheres covers 91% of the liquid surface trapping air in the gaps which adds to the thermal insulation properties. Reduces steaming - vapour losses reduced by 90%. Reduce vapours & splashing. No impedance to workload.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Draining Syphon
Allows the easy and quick emptying of water baths, immerse into water bath, squeeze the bellow and point the outlet to a bucket or sink.
Calibration Record
Factory Calibration record must be ordered with equipment.
PDF File Product Literature
Internal: 300w x 240d x 150h mm
Water level maximum: 130mm shelf fitted working depth 115mm
Packed: Packed: 38 x 23 x 29 cm
2. The shelf in the stainless steel tank provides a stable support for flasks/bottles/racks that can be removed for cleaning. The shelf is a low height design maximizing the working height in the bath, either needing less water when compared with traditional water baths or allowing tall containers or vessels to be immersed to a greater working depth. With lower water levels comes the benefit reduced heat up times and energy saving.
3. Three-year warranty and comprehensive customer support.
4. Broad range of accessories available to suit wide range of applications.
5. Before leaving our factory every water bath is identified with a unique serial number and undergoes a factory calibration adjusting control to known traceable value, electrically tested for safety at final inspection and a test certificate enclosed in rear of the instruction book.
6. Painted surfaces feature “anti-bacterial technology” which inhibits bacterial growth, improving hygiene requirements as demanded by clinical and laboratory environments. The Clifton range features easy to clean surfaces and finishes that are resistant to routine and efficient disinfections. The efficacy of the finish is maintained over time, as the anti-bacterial agent is integral within the paint finish.
Flat One Piece Stainless Steel Lid for 8 Litre Baths
1. Prevents contamination of liquid from airbourne particles.
2. Saves energy when the bath is in use by reducing heat losses.
3. Insulated handle.
Lift Off Gable Lid to suit 8 and 10 Litre Unstirred and Shaking Water baths
Clifton® clear Gable Lids helps reduce evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These gable lids with a high profile allows extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use
Stainless Steel Gable Lid to fit 8 and 10 Litre Unstirred and Shaking Water Baths
Clifton® Stainless steel Gable Lids helps reduce evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These stainless steel gable lids with a high profile allows extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use
Hinged Gable Lid to suit 8 and 10 Litre Unstirred and Shaking Water Baths
Using conventional lift off lids when removed from a water bath, condensation runs all over your bench top, a mess to clean up. Where do you put the lid once removed?
Hinged lids have a number of benefits in use over lift off lids. They simply hinge open 90° and stay open and any condensation collects in the lid, samples/work can be easily removed or placed in water bath. Close the lid and all the collected condensation runs into rear of the water bath. No mess. The hinge lid can be removed easily and quickly for cleaning or access.
4 x 83mm Stainless Steel Concentric Ringed Lid to suit 8 Litre Unstirred Baths
The lid and rings are manufactured from stainless steel. The concentric rings provide varying hole diameters in the lid. In use the lid minimises evaporation and maintains temperature stability of the water bath when tall vessels are being heated at elevated temperatures.
2 x 114mm Stainless Steel Concentric Ringed Lid to suit 8 Litre Unstirred Baths
The lid and rings are manufactured from stainless steel. The concentric rings provide varying hole diameters in the lid. In use the lid minimises evaporation and maintains temperature stability of the water bath when tall vessels are being heated at elevated temperatures.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Draining Syphon
Allows the easy and quick emptying of water baths, immerse into water bath, squeeze the bellow and point the outlet to a bucket or sink.
Stainless Steel Wire Basket for 8 Litre Baths
Stainless steel. Baskets recommended for use with Ultrasonic baths.
Polypropylene Spheres
This blanket of hollow spheres is ideal for open tanks of water. Reduces thermal losses - Savings of up to 75% can be achieved with a single layer - Increase energy saving & reducing costs. A single layer of spheres covers 91% of the liquid surface trapping air in the gaps which adds to the thermal insulation properties. Reduces steaming - vapour losses reduced by 90%. Reduce vapours & splashing. No impedance to workload.
Calibration Record
Factory Calibration record must be ordered with equipment.
Internal: 325w x 300d x 150h mm
Water level maximum: 130mm shelf fitted working depth 115mm
Packed: 38 x 23 x 29 cm
Comprising of a high quality corrosion resistant stainless steel tank, with a bright clean finish housed in a durable paint finished outer case. Painted surfaces feature anti-bacterial finish with good chemical resistance. Fitted with side lifting handles for ease of transportation.
Heaters and temperature sensor concealed under the tank providing a clutter free working area easy to wipe clean.
Supplied with a removable sturdy low height stainless steel perforated shelf, for even heat distribution. The shelf provides a deeper volume of water, for standing containers and accessory test tube racks in the bath.
Temperatures can be easily and rapidly set with the push button, wipe clean control panel.
Temperature setting is retained in memory, even after ‘power off’.
Illuminated on/off switch and heater indication lamp.
We verify the performance of every bath calibrating its controls and water temperature for consistent temperature control in use.
IP rated clear booted on/off mains switch.
Bath fitted with nonslip rubber feet.
Covering the bath with a lid reduces energy consumption and running costs.
This range of baths is not designed for boiling, the NE1B Boiling Bath range is recommended.
The lower the figure, the less energy used. Information supplied for size and range comparison, guidance only and measured consumption at set point. Please remember that the energy consumption may vary due to factors such as its location, ventilation, ambient temperatures and loading.
2. The shelf in the stainless steel tank provides a stable support for flasks/bottles/racks that can be removed for cleaning. The shelf is a low height design maximizing the working height in the bath, either needing less water when compared with traditional water baths or allowing tall containers or vessels to be immersed to a greater working depth. With lower water levels comes the benefit reduced heat up times and energy saving.
3. Three-year warranty and comprehensive customer support.
4. Broad range of accessories available to suit wide range of applications.
5. Before leaving our factory every water bath is identified with a unique serial number and undergoes a factory calibration adjusting control to known traceable value, electrically tested for safety at final inspection and a test certificate enclosed in rear of the instruction book.
6. Painted surfaces feature “anti-bacterial technology” which inhibits bacterial growth, improving hygiene requirements as demanded by clinical and laboratory environments. The Clifton range features easy to clean surfaces and finishes that are resistant to routine and efficient disinfections. The efficacy of the finish is maintained over time, as the anti-bacterial agent is integral within the paint finish.
Flat One Piece Stainless Steel Lid for 14 Litre Baths
Stainless steel flat lid minimizing heat loss, saving energy, and assisting to maintain bath temperature. Also when a Clifton water bath is 'not in use', with this lid fitted it prevents contamination of liquid from airbourne particles acts as a dust cover. The lid is fitted with an insulated handle.
Lift Off Gable Lid to suit 5, 14 and 18 Litre Unstirred Baths
Clifton Range® Clear Gable Lids helps reduce evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These lids with a high profile gable allows extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use
Stainless Steel Gable Lid to fit 5 and 14 Litre Unstirred Baths
Clifton® Stainless steel Gable Lids helps reduce evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These stainless steel gable lids with a high profile allows extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use
Stainless Steel Hinged Gable Lid to suit 14 Litre Unstirred Baths
Clifton® Stainless steel hinged Gable Lids reduces evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These stainless steel gable lids with a high profile design allows extended use of the bath, right into the edges of the tank. No drip points and condensate returns back into the bath.
Hinged lids have a number of benefits in use over lift off lids, these simply hinge open, any condensation collects in the lid, samples can be easily removed or placed in water bath. Close the lid and all the collected condensation runs into rear of the water bath. No mess.
Hinged Gable Lid to suit 14 Litre Unstirred Baths
Using conventional lift off lids when removed from a water bath, condensation runs all over your bench top, a mess to clean up. Where do you put the lid once removed?
Hinged lids have a number of benefits in use over lift off lids. They simply hinge open 90° and stay open and any condensation collects in the lid, samples/work can be easily removed or placed in water bath. Close the lid and all the collected condensation runs into rear of the water bath. No mess. The hinge lid can be removed easily and quickly for cleaning or access.
4 x 114mm Stainless Steel Concentric Ringed Lid to suit 14 Litre Unstirred Baths
The lid and rings are manufactured from stainless steel. The concentric rings provide varying hole diameters in the lid. In use the lid minimises evaporation and maintains temperature stability of the water bath when tall vessels are being heated at elevated temperatures.
6 x 83mm Stainless Steel Concentric Ringed Lid to suit 14 Litre Unstirred Baths
The lid and rings are manufactured from stainless steel. The concentric rings provide varying hole diameters in the lid. In use the lid minimises evaporation and maintains temperature stability of the water bath when tall vessels are being heated at elevated temperatures.
Stainless Steel Wire Basket for 14 Litre Baths
Stainless steel. Baskets recommended for use with Ultrasonic baths.
Polypropylene Spheres
This blanket of hollow spheres is ideal for open tanks of water. Reduces thermal losses - Savings of up to 75% can be achieved with a single layer - Increase energy saving & reducing costs. A single layer of spheres covers 91% of the liquid surface trapping air in the gaps which adds to the thermal insulation properties. Reduces steaming - vapour losses reduced by 90%. Reduce vapours & splashing. No impedance to workload.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Draining Syphon
Allows the easy and quick emptying of water baths, immerse into water bath, squeeze the bellow and point the outlet to a bucket or sink.
Calibration Record
Factory Calibration record must be ordered with equipment.
PDF File Product Literature
Internal: 500w x 300d x 150h mm
Water level maximum: 130mm shelf fitted working depth 115mm
Packed: 62 x 41 x 37 cm
Comprising of a high quality corrosion resistant stainless steel tank, with a bright clean finish housed in a durable paint finished outer case. Painted surfaces feature anti-bacterial finish with good chemical resistance. Fitted with side lifting handles for ease of transportation.
Heaters and temperature sensor concealed under the tank providing a clutter free working area easy to wipe clean.
Supplied with a removable sturdy low height stainless steel perforated shelf, for even heat distribution. The shelf provides a deeper volume of water, for standing containers and accessory test tube racks in the bath.
Temperatures can be easily and rapidly set with the push button, wipe clean control panel.
Temperature setting is retained in memory, even after ‘power off’.
Illuminated on/off switch and heater indication lamp. We verify the performance of every bath calibrating its controls and water temperature for consistent temperature control in use.
IP rated clear booted on/off mains switch.
Bath fitted with nonslip rubber feet.
Covering the bath with a lid reduces energy consumption and running costs.
This range of baths is not designed for boiling, the NE1B Boiling Bath range is recommended.
The lower the figure, the less energy used. Information supplied for size and range comparison, guidance only and measured consumption at set point. Please remember that the energy consumption may vary due to factors such as its location, ventilation, ambient temperatures and loading.
2. The shelf in the stainless steel tank provides a stable support for flasks/bottles/racks that can be removed for cleaning. The shelf is a low height design maximizing the working height in the bath, either needing less water when compared with traditional water baths or allowing tall containers or vessels to be immersed to a greater working depth. With lower water levels comes the benefit reduced heat up times and energy saving.
3. Three-year warranty and comprehensive customer support.
4. Broad range of accessories available to suit wide range of applications.
5. Before leaving our factory every water bath is identified with a unique serial number and undergoes a factory calibration adjusting control to known traceable value, electrically tested for safety at final inspection and a test certificate enclosed in rear of the instruction book.
6. Painted surfaces feature “anti-bacterial technology” which inhibits bacterial growth, improving hygiene requirements as demanded by clinical and laboratory environments. The Clifton range features easy to clean surfaces and finishes that are resistant to routine and efficient disinfections. The efficacy of the finish is maintained over time, as the anti-bacterial agent is integral within the paint finish.
Lift Off Gable Lid to suit 9, 22 and 28 Litre Unstirred and Shaking Water Baths
Clifton® clear Gable Lids helps reduce evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These gable lids with a high profile allows extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use
Hinged Gable Lid to suit 22 and 28 Litre Unstirred and Shaking Water Baths
Using conventional lift off lids when removed from a water bath, condensation runs all over your bench top, a mess to clean up. Where do you put the lid once removed?
Hinged lids have a number of benefits in use over lift off lids. They simply hinge open 90° and stay open and any condensation collects in the lid, samples/work can be easily removed or placed in water bath. Close the lid and all the collected condensation runs into rear of the water bath. No mess. The hinge lid can be removed easily and quickly for cleaning or access.
Stainless Steel Gable Lid to fit 22 and 28 Litre Unstirred and Shaking Water Baths
Clifton® Stainless steel Gable Lids helps reduce evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These stainless steel gable lids with a high profile allows extended use of the bath, right into the edges of the tank. No drip points to contaminate samples whilst the lid design ensures all condensate returns back into the bath. Insulated handles for safe use
Stainless Steel Hinged Gable Lid to fit 22 and 28 Litre Unstirred and Shaking Water Baths
Clifton® Stainless steel hinged Gable Lids reduces evaporation, assists in keeping samples in a water bath free from contamination and saves energy. These stainless steel gable lids with a high profile design allows extended use of the bath, right into the edges of the tank. No drip points and condensate returns back into the bath.
Hinged lids have a number of benefits in use over lift off lids, these simply hinge open, any condensation collects in the lid, samples can be easily removed or placed in water bath. Close the lid and all the collected condensation runs into rear of the water bath. No mess.
Flat One Piece Stainless Steel Lid for 22 Litre Baths
Stainless steel flat lid minimizing heat loss, saving energy, and assisting to maintain bath temperature. Also when a Clifton water bath is 'not in use', with this lid fitted it prevents contamination of liquid from airbourne particles acts as a dust cover. The lid is fitted with an insulated handle.
Stainless Steel Ringed Lid to fit 9, 22 & 28 Litre Unstirred Baths 6 x 114mm Holes
The lid and rings are manufactured from stainless steel. The concentric rings provide varying hole diameters in the lid. In use the lid minimises evaporation and maintains temperature stability of the water bath when tall vessels are being heated at elevated temperatures.
Polypropylene Spheres
This blanket of hollow spheres is ideal for open tanks of water. Reduces thermal losses - Savings of up to 75% can be achieved with a single layer - Increase energy saving & reducing costs. A single layer of spheres covers 91% of the liquid surface trapping air in the gaps which adds to the thermal insulation properties. Reduces steaming - vapour losses reduced by 90%. Reduce vapours & splashing. No impedance to workload.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Wire Basket for 22 Litre Baths
Stainless steel. Baskets recommended for use with Ultrasonic baths.
Drain Tap - for Water baths with serial numbers greater than 75100
1. Providing a gated on/off valve to empty fluids conveniently from the bath.
2. Nozzle supplied with tap for laboratory tubing.
Draining Syphon
Allows the easy and quick emptying of water baths, immerse into water bath, squeeze the bellow and point the outlet to a bucket or sink.
Calibration Record
Factory Calibration record must be ordered with equipment.
PDF File Product Literature