Internal: 320w x 180d x 240h mm
Packed:: 85x75x75cm
These Incubators can run at set temperature immediately, use run back timer or enable a delay start feature. Can be configured for gravity convection or with variable fan speed providing forced air circulation within the chamber.
The chamber is constructed from high quality stainless steel, lagged with high efficiency thermal insulation, all contained within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to robust design, insulation, a tight door closure with silicone seal and hinge design to maintain chamber temperatures with intelligent temperature control..
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
- 10 mins
- 5 mins
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
- Incubation of samples for microbiological analysis.
- Analysis of thermal resistance of samples subjected to higher temperatures.
- Antibody testing.
- Bacteria testing.
- Crystallisation observations
- Cultivation of thermophilic micro-organisms
- Pharma stability tests
- Food industry testing.
Temperature fluctuation measurements are based on temperature readings on shelf in center of the chamber.
Working capacity of chamber may be smaller.
Incubators up to 112 litres are stack-able.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Calibration Record
Factory Calibration record must be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
PDF File Product Literature
Internal: 400w x 250d x 320h mm
Packed: 65x54x69cm
These Incubators can run at set temperature immediately, use run
back timer or enable a delay start feature. Can be configured for
gravity convection or with variable fan speed providing forced air
circulation within the chamber.
The chamber is constructed from high quality stainless steel,
lagged with high efficiency thermal insulation, all contained
within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to
robust design, insulation, a tight door closure with silicone seal
and hinge design to maintain chamber temperatures with intelligent
temperature control..
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber
venting.
Fan chamber convection variable from 0% to 100%. Fan convection
improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port,
with perforated flap cover, to reduce heat losses when used with
external probes.
- 10 mins
- 5 mins
Features a temperature sensor fail alarm with error reporting on
LED screen.
Over temperature alarm is automatically set 5°C above set
point.
Door open heating is interrupted, after a short delay a door
sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit
protection.
- Incubation of samples for microbiological analysis.
- Analysis of thermal resistance of samples subjected to higher temperatures.
- Antibody testing.
- Bacteria testing.
- Crystallisation observations
- Cultivation of thermophilic micro-organisms
- Pharma stability tests
- Food industry testing.
- Before ordering please check the room or building access where this unit will be installed and electrical power requirements.
Temperature fluctuation measurements are based on temperature
readings on shelf in center of the chamber.
Working capacity of chamber may be smaller.
Incubators up to 112 litres are stack-able.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a
minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Internal: 400w x 400d x 360h mm
Packed: 75x73x90cm
These Incubators can run at set temperature immediately, use run
back timer or enable a delay start feature. Can be configured for
gravity convection or with variable fan speed providing forced air
circulation within the chamber.
The chamber is constructed from high quality stainless steel,
lagged with high efficiency thermal insulation, all contained
within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to
robust design, insulation, a tight door closure with silicone seal
and hinge design to maintain chamber temperatures with intelligent
temperature control..
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber
venting.
Fan chamber convection variable from 0% to 100%. Fan convection
improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port,
with perforated flap cover, to reduce heat losses when used with
external probes.
- 10 mins
- 10 mins
Features a temperature sensor fail alarm with error reporting on
LED screen.
Over temperature alarm is automatically set 5°C above set
point.
Door open heating is interrupted, after a short delay a door
sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit
protection.
- Incubation of samples for microbiological analysis.
- Analysis of thermal resistance of samples subjected to higher temperatures.
- Antibody testing.
- Bacteria testing.
- Crystallisation observations
- Cultivation of thermophilic micro-organisms
- Pharma stability tests
- Food industry testing.
Temperature fluctuation measurements are based on temperature readings on shelf in center of the chamber.
Working capacity of chamber may be smaller.
Incubators up to 112 litres are stack-able.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Wire Shelf for 56L.
Autoclaveable
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Rotary Mixer Disc Complete With 12 Clips for Tubes diameters between 15 - 17mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 6 Clips for Tube diameters between 25 - 30mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 16mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 25mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Internal: 400w x 450d x 620h mm
Packed: 80x80x105cm
These Incubators can run at set temperature immediately, use run
back timer or enable a delay start feature. Can be configured for
gravity convection or with variable fan speed providing forced air
circulation within the chamber.
The chamber is constructed from high quality stainless steel,
lagged with high efficiency thermal insulation, all contained
within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to
robust design, insulation, a tight door closure with silicone seal
and hinge design to maintain chamber temperatures with intelligent
temperature control.
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
- 10 mins
- 5 mins
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection..
- Incubation of samples for microbiological analysis.
- Analysis of thermal resistance of samples subjected to higher temperatures.
- Antibody testing.
- Bacteria testing.
- Crystallisation observations
- Cultivation of thermophilic micro-organisms
- Pharma stability tests
- Food industry testing.
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Incubators up to 112 litres are stack-able.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Rotary Mixer Disc Complete With 12 Clips for Tubes diameters between 15 - 17mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 24 Clips for Tube diameters between 8 - 11mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 6 Clips for Tube diameters between 25 - 30mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 16mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 25mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Internal: 600w x 510d x 800h mm
Packed: 94x84x130cm
These Incubators can run at set temperature immediately, use run
back timer or enable a delay start feature. Can be configured for
gravity convection or with variable fan speed providing forced air
circulation within the chamber.
The chamber is constructed from high quality stainless steel,
lagged with high efficiency thermal insulation, all contained
within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to
robust design, insulation, a tight door closure with silicone seal
and hinge design to maintain chamber temperatures with intelligent
temperature control.
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
- 28 mins
- 10 mins
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
- Incubation of samples for microbiological analysis.
- Analysis of thermal resistance of samples subjected to higher temperatures.
- Antibody testing.
- Bacteria testing.
- Crystallisation observations
- Cultivation of thermophilic micro-organisms
- Pharma stability tests
- Food industry testing.
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Incubators up to 112 litres are stack-able.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Rotary Mixer Disc Complete With 12 Clips for Tubes diameters between 15 - 17mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 24 Clips for Tube diameters between 8 - 11mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 6 Clips for Tube diameters between 25 - 30mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 16mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 25mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Internal: 800w x 510d x 1040h mm
Packed: 120x88x180cm
These Incubators can run at set temperature immediately, use run
back timer or enable a delay start feature. Can be configured for
gravity convection or with variable fan speed providing forced air
circulation within the chamber.
The chamber is constructed from high quality stainless steel,
lagged with high efficiency thermal insulation, all contained
within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to
robust design, insulation, a tight door closure with silicone seal
and hinge design to maintain chamber temperatures with intelligent
temperature control.
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
- 30 mins
- 10 mins
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
- Incubation of samples for microbiological analysis.
- Analysis of thermal resistance of samples subjected to higher temperatures.
- Antibody testing.
- Bacteria testing.
- Crystallisation observations
- Cultivation of thermophilic micro-organisms
- Pharma stability tests
- Food industry testing.
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in center of the chamber.
Working capacity of chamber may be smaller.
Incubators up to 112 litres are stack-able.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Rotary Mixer Disc Complete With 12 Clips for Tubes diameters between 15 - 17mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 24 Clips for Tube diameters between 8 - 11mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 6 Clips for Tube diameters between 25 - 30mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 16mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 25mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Internal: 1040w x 600d x 1200h mm
Packed: 135x92x211cm
These Incubators can run at set temperature immediately, use run
back timer or enable a delay start feature. Can be configured for
gravity convection or with variable fan speed providing forced air
circulation within the chamber.
The chamber is constructed from high quality stainless steel,
lagged with high efficiency thermal insulation, all contained
within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to
robust design, insulation, a tight door closure with silicone seal
and hinge design to maintain chamber temperatures with intelligent
temperature control.
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
- 30 mins
- 10 mins
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
- Incubation of samples for microbiological analysis.
- Analysis of thermal resistance of samples subjected to higher temperatures.
- Antibody testing.
- Bacteria testing.
- Crystallisation observations
- Cultivation of thermophilic micro-organisms
- Pharma stability tests
- Food industry testing.
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Incubators up to 112 litres are stack-able.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Rotary Mixer Disc Complete With 12 Clips for Tubes diameters between 15 - 17mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 24 Clips for Tube diameters between 8 - 11mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 locating on three pins then secured in place with thumb wheel.
Rotary Mixer Disc Complete With 6 Clips for Tube diameters between 25 - 30mm
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 16mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Carousel for tubes up to 25mm diameter
1. The range of accessories can also be autoclaved and allow for easy loading and tube removal.
2. The accessory is easy to fit onto the RM-1 or RM-2 locating on three pins then secured in place with thumb wheel.
Stainless Steel Test Tube Rack 26 Holes x 17mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 16mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 25mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter - also suitable for 1.5ml micro tubes
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 12mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 18mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.
Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter
Laboratory Test Tube rack, stainless steel 304 spec 18/8 non-magnetic, bright finish. Supplied flat packed ready for assembly. Suitable for test tubes with an external diameter 31mm.
Can be cleaned with detergents, ultrasonics or autoclaved. Durable and stable in use with looped handles for easy retrieval from hot water baths.