Dimensions
External: 520w x 390d x 600h mm
Internal: 320w x 180d x 240h mm
Packed: 85 x 75 x 75cm
Internal: 320w x 180d x 240h mm
Packed: 85 x 75 x 75cm
Capacity
15 litre chamber Working capacity of the chamber can be smaller.
Temperature Range
ambient +5°C to 300°C
Temperature Alarm
Over temperature alarm is automatically set 5°C above set point
Temperature Control
PID Digital, LED display showing actual or set temperature, resolution 0.1°C
Temperature Sensor
pt100 with control diagnostics at power up
Temperature Fluctuation
±0.4°C @ 150°C Measurements based on temperature readings on shelf in centre of the chamber.
Temperature Variation
±1.8°C @ 150°C Measured in vertical axis in the chamber using Wired Shelves.
Temperature Control & Run Back Timer
Visual indicator and end messaging 00:01 to 99:59 (hh:mm) activates at set temp
Temperature Control & Delay Start Timer
Heating commences at a set time in the future, within 24 hours
Chamber convection
Fan speed can be set from 0% gravity convection within the chamber variable to 100% for forced air convection.
Exhaust air flap
Adjustable 0 to 100% chamber venting
Access Port
35mm port size, perforated flap cover helps to reduce losses when fitting independent external probes or thermocouples.
Door configuration
Single insulated door, lockable with 2 point door engagement for an even seal
Door Alarm
Door open, heating interrupted, delay before door sounder chimes until door closed, heating resumes
Shelves fitted & maximum
1 wire / 3 max stainless steel
Shelving Locations
Available every 20mm vertically
Shelf Maximum Load
10kg
Heater Power
1050W
Voltage
230V 50/60Hz
Stackable
Yes
Feet/Castors
Levelling Feet
Packed Weight
27 kg
Product Code
Description
These Ovens can run at set temperature immediately, use run back timer or enable a delay start feature. Can be configured for gravity convection or with variable fan speed providing forced air circulation within the chamber.
The Oven chamber is constructed from high quality stainless steel, lagged with high efficiency thermal insulation, all contained within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to robust design, insulation, a tight door closure with silicone seal and hinge design to maintain chamber temperatures with intelligent temperature control.
Controls
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
Heat-up Times
- 25 mins
Temperature Door open recovery
- 5 mins
Safety Features
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
Safety Class
Warranty
Notes
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Drying Ovens up to 112 litres are stackable.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
PDF File Product Literature
Dimensions
External: 600w x 460d x 680h mm
Internal: 400w x 250d x 320h mm
Packed: 65 x 54 x 69cm
Internal: 400w x 250d x 320h mm
Packed: 65 x 54 x 69cm
Capacity
32 litre chamber Working capacity of the chamber can be smaller.
Temperature Range
ambient +5°C to 300°C
Temperature Alarm
Over temperature alarm is automatically set 5°C above set point
Temperature Control
PID Digital, LED display showing actual or set temperature, resolution 0.1°C
Temperature Sensor
pt100 with control diagnostics at power up
Temperature Fluctuation
±0.4°C @ 150°C Measurements based on temperature readings on shelf in centre of the chamber.
Temperature Variation
±1.8°C @ 150°C Measured in vertical axis in the chamber using Wired Shelves.
Temperature Control & Run Back Timer
Visual indicator and end messaging 00:01 to 99:59 (hh:mm) activates at set temp
Temperature Control & Delay Start Timer
Heating commences at a set time in the future, within 24 hours
Chamber convection
Fan speed can be set from 0% gravity convection within the chamber variable to 100% for forced air convection.
Exhaust air flap
Adjustable 0 to 100% chamber venting
Access Port
35mm port size, perforated flap cover helps to reduce losses when fitting independent external probes or thermocouples.
Door configuration
Single insulated door, lockable with 2 point door engagement for an even seal
Door Alarm
Door open, heating interrupted, delay before door sounder chimes until door closed, heating resumes
Shelves fitted & maximum
1 wire / 3 max stainless steel
Shelving Locations
Available every 20mm vertically
Shelf Maximum Load
20kg
Heater Power
1100W
Voltage
230V 50/60Hz
Stackable
Yes
Feet/Castors
Levelling Feet
Packed Weight
37kg
Product Code
Description
These Ovens can run at set temperature immediately, use run back
timer or enable a delay start feature. Can be configured for
gravity convection or with variable fan speed providing forced air
circulation within the chamber.
The Oven chamber is constructed from high quality stainless
steel, lagged with high efficiency thermal insulation, all
contained within an outer steel housing with anti-bacterial paint
finish.
With energy efficiency in mind, particular attention is paid to robust design, insulation, a tight door closure with silicone seal and hinge design to maintain chamber temperatures with intelligent temperature control.
Controls
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
Heat-up Times
- 25 mins
Temperature Door open recovery
- 5 mins
Safety Features
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
Safety Class
Warranty
Notes
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Drying Ovens up to 112 litres are stackable.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Dimensions
External: 600w x 605d x 720h mm
Internal: 400w x 400d x 360h mm
Packed: 75x73x90cm
Internal: 400w x 400d x 360h mm
Packed: 75x73x90cm
Capacity
Nominal Tank Capacity: 56 litre chamber Working capacity of the chamber can be smaller.
Temperature Range
ambient +5°C to 300°C
Temperature Alarm
Over temperature alarm is automatically set 5°C above set point
Temperature Control
PID Digital, LED display showing actual or set temperature, resolution 0.1°C
Temperature Sensor
pt100 with control diagnostics at power up
Temperature Fluctuation
±0.4°C @ 150°C Measurements based on temperature readings on shelf in centre of the chamber.
Temperature Variation
±1.8°C @ 150°C Measured in vertical axis in the chamber using Wired Shelves.
Temperature Control & Run Back Timer
Visual indicator and end messaging 00:01 to 99:59 (hh:mm) activates at set temp
Temperature Control & Delay Start Timer
Heating commences at a set time in the future, within 24 hours
Chamber convection
Fan speed can be set from 0% gravity convection within the chamber variable to 100% for forced air convection.
Exhaust air flap
Adjustable 0 to 100% chamber venting
Access Port
35mm port size, perforated flap cover helps to reduce losses when fitting independent external probes or thermocouples.
Door configuration
Single insulated door, lockable with 2 point door engagement for an even seal
Door Alarm
Door open, heating interrupted, delay before door sounder chimes until door closed, heating resumes
Shelves fitted & maximum
2 wire / 5 max stainless steel
Shelving Locations
Available every 20mm vertically
Shelf Maximum Load
20kg
Heater Power
2150W
Voltage
230V 50/60Hz
Stackable
Yes
Feet/Castors
Levelling Feet
Packed Weight
61kg
Product Code
Description
These Ovens can run at set temperature immediately, use run back
timer or enable a delay start feature. Can be configured for
gravity convection or with variable fan speed providing forced air
circulation within the chamber.
The Oven chamber is constructed from high quality stainless steel,
lagged with high efficiency thermal insulation, all contained
within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to
robust design, insulation, a tight door closure with silicone seal
and hinge design to maintain chamber temperatures with intelligent
temperature control.
Controls
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
Heat up times
- 25 mins
Temperature Door open recovery
- 5 mins
Safety Features
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
Safety Class
Warranty Period
Notes
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Drying Ovens up to 112 litres are stackable.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Wire Shelf for 56L.
Autoclaveable
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Dimensions
External: 650w x 660d x 980h mm
Internal: 400w x 450d x 620h mm
Packed: 80x80x105cm
Internal: 400w x 450d x 620h mm
Packed: 80x80x105cm
Capacity
Nominal Tank Capacity: 112 litre chamber Working capacity of the chamber can be smaller.
Temperature Range
Ambient +5°C to 300°C
Temperature Alarm
Over temperature alarm is automatically set 5°C above set point
Temperature Control
PID Digital, LED display showing actual or set temperature, resolution 0.1°C
Temperature Sensor
pt100 with control diagnostics at power up
Temperature Fluctuation
±0.4°C @ 150°C Measurements based on temperature readings on shelf in centre of the chamber.
Temperature Variation
±1.8°C @ 150°C Measured in vertical axis in the chamber using Wired Shelves.
Temperature Control & Run Back Timer
Visual indicator and end messaging 00:01 to 99:59 (hh:mm) activates at set temp
Temperature Control & Delay Start Timer
Heating commences at a set time in the future, within 24 hours
Chamber convection
Fan speed can be set from 0% gravity convection within the chamber variable to 100% for forced air convection.
Exhaust air flap
Adjustable 0 to 100% chamber venting
Access Port
35mm port size, perforated flap cover helps to reduce losses when fitting independent external probes or thermocouples.
Door configuration
Single insulated door, lockable with 2 point door engagement for an even seal
Door Alarm
Door open, heating interrupted, delay before door sounder chimes until door closed, heating resumes
Shelves fitted & maximum
2 wire / 8 max stainless steel
Shelving Locations
Available every 20mm vertically
Shelf Maximum Load
20kg
Heater Power
2150W
Voltage
230V 50/60Hz
Stackable
Yes
Feet/Castors
Levelling Feet
Packed Weight
85kg
Product Code
Description
These Ovens can run at set temperature immediately, use run back timer or enable a delay start feature. Can be configured for gravity convection or with variable fan speed providing forced air circulation within the chamber.
The Oven chamber is constructed from high quality stainless steel, lagged with high efficiency thermal insulation, all contained within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to robust design, insulation, a tight door closure with silicone seal and hinge design to maintain chamber temperatures with intelligent temperature control.
Controls
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
Heat-up Times
- 25 mins
Temperature Door open recovery
- 5 mins
Fan speed
Safety Features
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
Safety Class
Warranty Period
Notes
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Drying Ovens up to 112 litres are stackable.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Dimensions
External: 800w x 720d x 1160h mm
Internal: 600w x 510d x 800h mm
Packed: 94x84x130cm
Internal: 600w x 510d x 800h mm
Packed: 94x84x130cm
Capacity
Nominal Tank Capacity: 240 litre chamber Working capacity of the chamber can be smaller.
Temperature Range
Ambient +5°C to 300°C
Temperature Alarm
Over temperature alarm is automatically set 5°C above set point
Temperature Control
PID Digital, LED display showing actual or set temperature, resolution 0.1°C
Temperature Sensor
pt100 with control diagnostics at power up
Temperature Fluctuation
±0.4°C @ 150°C Measurements based on temperature readings on shelf in centre of the chamber.
Temperature Variation
±1.8°C @ 150°C Measured in vertical axis in the chamber using Wired Shelves.
Temperature Control & Run Back Timer
Visual indicator and end messaging 00:01 to 99:59 (hh:mm) activates at set temp
Temperature Control & Delay Start Timer
Heating commences at a set time in the future, within 24 hours
Chamber convection
Fan speed can be set from 0% gravity convection within the chamber variable to 100% for forced air convection.
Exhaust air flap
Adjustable 0 to 100% chamber venting
Access Port
35mm port size, perforated flap cover helps to reduce losses when fitting independent external probes or thermocouples.
Door configuration
Single insulated door, lockable with 2 point door engagement for an even seal
Door Alarm
Door open, heating interrupted, delay before door sounder chimes until door closed, heating resumes
Shelves fitted & maximum
3 wire / 10 max stainless steel
Shelving Locations
Available every 20mm vertically
Shelf Maximum Load
20kg
Heater Power
3200W
Voltage
230V 50/60Hz Blue Power plug 2P+E
Stackable
No
Feet/Castors
Levelling Feet
Packed Weight
150kg
Product Code
Description
These Ovens can run at set temperature immediately, use run back timer or enable a delay start feature. Can be configured for gravity convection or with variable fan speed providing forced air circulation within the chamber.
The Oven chamber is constructed from high quality stainless steel, lagged with high efficiency thermal insulation, all contained within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to robust design, insulation, a tight door closure with silicone seal and hinge design to maintain chamber temperatures with intelligent temperature control.
Controls
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
Heat-up Times
- 25 mins
Temperature Door open recovery
- 5 mins
Safety Features
Features a temperature sensor fail alarm with error reporting on LCD screen.
Power failure control with auto resume and event recording.
Setting of High and Low temperature Alarm, settable 0-5°C about set temperature.
Door opening generates an audible beep and indication on LCD display. When a program is running and should the door be left open a Door Alarm occurs, illuminating a red warning indicator and audible beeping until closed. Door open Alarm settable 0-5 minutes.
Over temperature protection can be selected in controls: Class 1
for overall unit protection or Class 2 for experiment/sample
protection. Once protection is activated heating is switched off
and a warning appears on screen. Class 3 protection, an accessory
factory fit option, provides active protection once the temperature
in chamber returns to normal values heating and control
resumes.
Safety Class
Warranty Period
Notes
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Drying Ovens up to 112 litres are stackable.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Dimensions
External: 1000w x 720d x 1470h mm
Internal: 800w x 510d x 1040h mm
Packed: 120x88x180cm
Internal: 800w x 510d x 1040h mm
Packed: 120x88x180cm
Capacity
Nominal Tank Capacity: 400 litre chamber Working capacity of the chamber can be smaller.
Temperature Range
ambient +5°C to 300°C
Temperature Alarm
Over temperature alarm is automatically set 5°C above set point
Temperature Control
PID Digital, LED display showing actual or set temperature, resolution 0.1°C
Temperature Sensor
pt100 with control diagnostics at power up
Temperature Fluctuation
±0.8°C @ 150°C Measurements based on temperature readings on shelf in centre of the chamber.
Temperature Variation
±2.5°C @ 150°C Measured in vertical axis in the chamber using Wired Shelves.
Temperature Control & Run Back Timer
Visual indicator and end messaging 00:01 to 99:59 (hh:mm) activates at set temp
Temperature Control & Delay Start Timer
Heating commences at a set time in the future, within 24 hours
Chamber convection
Fan speed can be set from 0% gravity convection within the chamber variable to 100% for forced air convection.
Exhaust air flap
Adjustable 0 to 100% chamber venting
Access Port
35mm port size, perforated flap cover helps to reduce losses when fitting independent external probes or thermocouples.
Door configuration
Double insulated door, lockable with 2 point door engagement for an even seal
Door Alarm
Door open, heating interrupted, delay before door sounder chimes until door closed, heating resumes
Shelves fitted & maximum
3 wire / 14 max stainless steel
Shelving Locations
Available every 20mm vertically
Shelf Maximum Load
20kg
Heater Power
4250W
Voltage
230V 50/60Hz Blue Power plug 2P+E
Stackable
No
Feet/Castors
Levelling Castor
Packed Weight
250kg
Product Code
Description
These Ovens can run at set temperature immediately, use run back timer or enable a delay start feature. Can be configured for gravity convection or with variable fan speed providing forced air circulation within the chamber.
The Oven chamber is constructed from high quality stainless steel, lagged with high efficiency thermal insulation, all contained within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to robust design, insulation, a tight door closure with silicone seal and hinge design to maintain chamber temperatures with intelligent temperature control.
Controls
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
Heat-up Times
- 35 mins
Temperature Door open recovery
- 10 mins
Safety Features
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
Safety Class
Warranty Period
Notes
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Drying Ovens up to 112 litres are stackable.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Additional program functionality with temperature and time ramps. Factory installation at time models ordered.
Factory installation at time models ordered.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.
Dimensions
External: 1240w x 810d x 1625h mm
Internal: 1040w x 600d x 1200h mm
Packed: 135x92x211cm
Internal: 1040w x 600d x 1200h mm
Packed: 135x92x211cm
Capacity
Nominal Tank Capacity: 750 litre chamber Working capacity of the chamber can be smaller.
Temperature Range
ambient +5°C to 300°C
Temperature Alarm
Over temperature alarm is automatically set 5°C above set point
Temperature Control
PID Digital, LED display showing actual or set temperature, resolution 0.1°C
Temperature Sensor
pt100 with control diagnostics at power up
Temperature Fluctuation
±0.8°C @ 150°C Measurements based on temperature readings on shelf in centre of the chamber.
Temperature Variation
±2.5°C @ 150°C Measured in vertical axis in the chamber using Wired Shelves.
Temperature Control & Run Back Timer
Visual indicator and end messaging 00:01 to 99:59 (hh:mm) activates at set temp
Temperature Control & Delay Start Timer
Heating commences at a set time in the future, within 24 hours
Chamber convection
Fan speed can be set from 0% gravity convection within the chamber variable to 100% for forced air convection.
Exhaust air flap
Adjustable 0 to 100% chamber venting
Access Port
35mm port size, perforated flap cover helps to reduce losses when fitting independent external probes or thermocouples
Door configuration
Double insulated door, lockable with 2 point door engagement for an even seal
Door Alarm
Door open, heating interrupted, delay before door sounder chimes until door closed, heating resumes
Shelves fitted & maximum
5 wire / 16 max stainless steel
Shelving Locations
Available every 20mm vertically
Shelf Maximum Load
20kg
Heater Power
5250W
Voltage
230V 50/60Hz Blue Power plug 2P+E
Stackable
No
Packed Weight
380kg
Product Code
Description
These Ovens can run at set temperature immediately, use run back timer or enable a delay start feature. Can be configured for gravity convection or with variable fan speed providing forced air circulation within the chamber.
The Oven chamber is constructed from high quality stainless steel, lagged with high efficiency thermal insulation, all contained within an outer steel housing with anti-bacterial paint finish.
With energy efficiency in mind, particular attention is paid to robust design, insulation, a tight door closure with silicone seal and hinge design to maintain chamber temperatures with intelligent temperature control.
Controls
On/off power switch.
Exhaust air flap is dial adjustable from 0 to 100% for chamber venting.
Fan chamber convection variable from 0% to 100%. Fan convection improves temperature uniformity and heating recovery time.
Door, lockable with 2 point door engagement for an even seal.
On left hand side the Oven features a 35mm diameter Access port, with perforated flap cover, to reduce heat losses when used with external probes.
Heat-up Times
- 35 mins
Temperature Door open recovery
- 10 mins
Safety Features
Features a temperature sensor fail alarm with error reporting on LED screen.
Over temperature alarm is automatically set 5°C above set point.
Door open heating is interrupted, after a short delay a door sounder chimes until door closed, heating resumes.
Fitted with Class 1 over temperature thermostat for overall unit protection.
Safety Class
Warranty Period
Notes
- Before ordering please check the room or building access
where this unit will be installed and electrical power
requirements.
Temperature fluctuation measurements are based on temperature readings on shelf in centre of the chamber.
Working capacity of chamber may be smaller.
Drying Ovens up to 112 litres are stackable.
Do not place in direct sunlight or near a heat or cold source.
Allow a 100mm air gap away from wall at rear. Ensure there is a minimum 300mm air gap from top of the unit to ceiling.
Temperature survey chamber, 9 point, at a specific temperature, factory Calibration Record
Tot be ordered with equipment.
Temperature survey chamber, 27 point, at a specific temperature, factory Calibration Record
This to be ordered with equipment.
Calibration Record
Factory Calibration record must be ordered with equipment.