Education Equipment

1020G

130 x 85mm Stainless steel Gas Bath

« Return to Education Equipment

Capacity, brimful
1 litre
Product Code
1020G
Description
Suitable for use with hotplate or gas burner, the steam produced from bath, provides an effective source of constant heat for samples that otherwise could be thermally damaged by a naked flame.

Supplied with a set of rings to vary the diameter of the bath aperture.

By removing concentric rings, the hole sizes can be varied to accommodate different sizes of vessels 95, 77, 58, 42, 30mm

No accessories available for this product.

1021G

160 x 104mm Stainless steel Gas Bath

« Return to Education Equipment

Capacity, brimful
2 litre
Product Code
1021G
Description
Suitable for use with hotplate or gas burner, the steam produced from bath, provides an effective source of constant heat for samples that otherwise could be thermally damaged by a naked flame.

Supplied with a set of rings to vary the diameter of the bath aperture.

By removing concentric rings, the hole sizes can be varied to accommodate different sizes of vessels 119, 102, 77, 58, 42, 30mm

No accessories available for this product.

NE1-2.5E

2.5 Litre Unstirred Thermostatic Bath - small

« Return to Education Equipment

Dimensions
External: 270 w x 190d x 240h mm
Internal: 230w x 130d x 150h mm
Water level: : Maximum 130mm shelf fitted working depth 115mm
Packed: 25 x 13 x 39 cm
Capacity
Nominal Tank Capacity: 2.5 Litres
Temperature Range
Ambient + 5°C - 100°C will operate at 100°C but not designed for continuous boiling, we recommend NE1B Boiling Baths
Temperature control
analogue dial pointer graduated in 5°C divisions
Sensitivity
±0.5°C
Uniformity
±0.5°C
Heater Power (220-240V)
250W
Voltage
230V 50-60Hz
Packed Weight
4.7kg
Product Code
NE1-2.5
Description
The NE1 series, Thermostatic Clifton analogue baths are designed for general use and are economically priced without compromising quality.

Comprising of a high quality corrosion resistant stainless steel tank, with a bright clean finish housed in a durable paint finished outer case. Painted surfaces feature anti-bacterial finish with good chemical resistance. Fitted with side lifting handles for ease of transportation.

Heaters and temperature sensor concealed under the tank providing a clutter free working area easy to wipe clean.

Supplied with a removable sturdy low height stainless steel perforated shelf, providing a taller volume of water, for standing containers and accessory test tube racks in the bath.
Controls
Easy to use analogue dial pointer for setting temperature, graduated in 5°C divisions.

Illuminated on/off switch and heater indication lamp.

We verify the performance of every bath calibrating its controls and water temperature at 45°C for consistent temperature control in use.
Safety
Thermal cut out fitted in the heater. IP rated clear booted on/off mains switch. Bath fitted with non-slip rubber feet.
Heat-up Times
  • 13 mins
  • 37 mins
  • 60 mins
Heating/Cooling Information
Above 60°C or below ambient it is recommended that to achieve optimum performance the bath should be covered with a Lid or layer of polypropylene spheres - see accessories.

Covering the bath with a lid reduces energy consumption and running costs.

This range of baths will operate at 100°C however are not designed for continuous boiling, the NE1B Boiling Bath range is recommended.
Power Consumption (220-240V)
250W
Energy Consumption
0.21kWh @ 37°C
0.22kWh @ 60°C - lid fitted

The lower the figure, the less energy used. Information supplied for size and range comparison, guidance only and measured consumption at set point. Please remember that the energy consumption may vary due to factors such as its location, ventilation, ambient temperatures and loading.
Warranty Period
3 Years
Features and Benefits
1.Clifton unstirred water baths are designed for immersion of flasks/bottles/racks in a highly stable temperature environment throughout the water bath. 2. The shelf in the stainless steel tank provides a stable support for flasks/bottles/racks that can be removed for cleaning. The shelf is a low height design maximizing the working height in the bath, either needing less water when compared with traditional water baths or allowing tall containers or vessels to be immersed to a greater working depth. With lower water levels comes the benefit reduced heat up times and energy saving. 3. Three-year warranty and comprehensive customer support. 4. Broad range of accessories available to suit wide range of applications. 5. Before leaving our factory each water bath has a unique serial number, electrically tested for safety at final inspection and a test certificate enclosed in rear of the instruction book. 6. To verify the performance of the temperature control system every unit undergoes a factory calibration adjusting control to known traceable values. 7. Painted surfaces feature “anti-bacterial technology” which inhibits bacterial growth, improving hygiene requirements as demanded by many clinical and laboratory environments. These hygienic surfaces are part of a controlled approach to cleaner facilities. The Clifton range features easy to clean surfaces and finishes that are resistant to routine and efficient disinfection’s. The efficacy of the finish is maintained over time, as the anti-bacterial agent is integral within the finishes.

Polypropylene Spheres

This blanket of hollow spheres is ideal for open tanks of water. Reduces thermal losses - Savings of up to 75% can be achieved with a single layer - Increase energy saving & reducing costs. A single layer of spheres covers 91% of the liquid surface trapping air in the gaps which adds to the thermal insulation properties. Reduces steaming - vapour losses reduced by 90%. Reduce vapours & splashing. No impedance to workload.

Flat One Piece Stainless Steel Lid for 2 and 4 Litre Baths

Stainless steel flat lid minimizing heat loss, saving energy, and assisting to maintain bath temperature. Also when a Clifton water bath is 'not in use', with this lid fitted it prevents contamination of liquid from airbourne particles acts as a dust cover. The lid is fitted with an insulated handle.

Thermometer Clip Complete With Bent Stem Spirit Filled Thermometer

Used as a reference to measure actual water temperature of the water bath. Thermometer range 0° to 100°C graduated in 2°C divisions.

Draining Syphon

Allows the easy and quick emptying of water baths, immerse into water bath, squeeze the bellow and point the outlet to a bucket or sink.

NE 010GE

Clifton Targa Centrifuge

« Return to Education Equipment

Dimensions
External: 361w x 400d x 320hmm Lid closed
Overall: 361w x 415d x 720h mm
Packed: 45 x 41 x 32cm
Rotor type
Swing out supplied
Capacity
Tube dimensions: 17mm diameter x 100mm Using standard buckets for 10ml or 15ml tubes
Tube dimensions with green adaptors: 13mm diameter x 75 Fitting Green adaptors, supplied, into top of each bucket, for 5 or 7ml tubes
Tube dimensions with grey adaptors: 10mm diameter x 75 Fitting Grey adaptors, supplied, into top of each bucket, for 1.5/2.0ml tubes
Maximum rotor speed
2800rpm
Maximum RCF
1100g
Maximum radius
130mm
Operation
Rotor activated push button Maintaining finger pressure on the push button operates the centrifuge and locks the lid in position. Releasing finger pressure de-energises the rotor.
Voltage
230V a.c. 50-60Hz
Packed Weight
11 kg
Product Code
NE 010GE
Description
The Targa centrifuge is designed specifically for the education market being a low cost, low energy product.

Constructed with a durable steel body for safety with four-place swing out rotor complete with removable buckets and tube adaptors.

Maintaining finger pressure on the push button operates the centrifuge and locks the lid in position. The rotor can only be energised when the lid is correctly closed and locked. A viewing window in the lid enables the rotor motion to be observed.

Releasing finger pressure de-energies the rotor


Easy wipe clean bowl with no crevices. The Rotor can be removed for easy cleaning.
Safety Features
Motor fitted with one shot overtemprature/overcurrent safety device.
Safety Class
1
Warranty Period
3 Years
Notes
With the swing out rotor and four bucket holders supplied, each bucket 17mm internal diameter, recommended Centrifuge tubes:

Clifton accessory tubes, refer to accessories.
Pyrex 1660/02M 16mm x 90mm - glass
Fisher TES-600-029R 10mm x 75mm - glass
Fisher TES-600-071S 16mm x 100mm.
Features and Benefits
1. Maintaining finger pressure on the push button operates the centrifuge and lock the lid in position. 2. The rotor can only be energised when the lid is correctly closed and locked. 3. Releasing finger pressure de-energises the rotor.

NE 010G Targa Centrifuge - Serial No 106800 >

PDF File   Instruction Books

NE 010G Targa Centrifuge - Serial No 55548>106800

PDF File   Instruction Books

Centrifuge Supplement Catalogue

PDF File   Product Literature

NE 010G Targa Centrifuge - Serial No < 55547

PDF File   Instruction Books

1026G

200 x 130mm Stainless steel Gas Bath

« Return to Education Equipment

Capacity, brimful
4 litres
Product Code
1026G
Description
Suitable for use with hotplate or gas burner, the steam produced from bath, provides an effective source of constant heat for samples that otherwise could be thermally damaged by a naked flame.

Supplied with a set of rings to vary the diameter of the bath aperture.

By removing concentric rings, the hole sizes can be varied to accommodate different sizes of vessels 140, 127, 102, 77, 58, 42, 30mm

No accessories available for this product.

BM-1

Breathing Monitor

« Return to Education Equipment

Dimensions
External: 538w x 332d x 290h mm
Internal: 500w x 300d x 200h mm
Packed: 600 x 400 330mm
Packed Weight
11kg
Product Code
BM-1
Description
The Breathing Monitor can be used for investigating tidal volumes, reserve volumes and vital capacity.

Constructed with a one piece stainless steel tank housed in a durable painted outer case. The float is constructed from lightweight plastic and calibrated 0 to 7 x 0.5 litres with a metal counterpoise. When the tank is filled with water the water the float chamber is contained.

In use the float will rise and fall, allowing readings to be taken directly off the float or it may be connected to a data logger with a motion sensor.

Supplied with a mouth piece that fits into the corrugated breathing hoses which snugly connects into Breathing Monitor.

Also included a nose clip and pen arm for fitting data logger sensors.
Warranty Period
1 year
Notes
Recommended data loggers:

Logit, from Breckland Scientific Supplies http://www.brecklandscientific.co.uk

Logit, from Griffin Education http://www.griffinandgeorge.co.uk

Data Harvest http://www.dataharvest.co.uk ask for data sheet DS120(1) from Data Harvest for setting up with Motion sensors.Scientific and Chemical http://www.sci-chem.co.uk

Data Harvest from Timstar http://www.timstar.co.uk ask for data sheet DS120(1)from Data Harvest for setting up with Motion sensors.

A pen arm is supplied to attach to the float with motion sensors/data loggers in mind.

BM-1 Breathing Monitor - Serial No. 85000 >

PDF File   Instruction Books

SM-1

Student Spirometer

« Return to Education Equipment

Dimensions
External: 720w x 320d x 230h mm
Packed: 800 x 430x 330mm
Product Code
SM-1
Description
The Spirometer can be used for investigating tidal volumes, respiratory rate, pulmonary ventilation, reserve volumes and vital capacity. Oxygen consumption can also be measured which is useful in metabolic studies.

A simple lever control enables the subject to be connected either to atmosphere or to the float for recording. A container for soda-lime crystals is fitted which can be used to absorb carbon dioxide. The spirometer is designed to offer minimum resistance to air flow. This means greater comfort for the subject and more realistic results. The tank is one piece stainless steel pressing housed in a durable painted outer case. The float is constructed from lightweight plastic. The float is calibrated 0 to 7 x 0.5 litres and has a metal counterpoise. The pen arm corresponds to approximately 0.5 litres.

Supplied with a mouth piece that fits into the corrugated breathing hoses which snugly connects into Spirometer.

Also included a nose clip and pen arm for fitting data logger sensors.
Safety Features
INVESTIGATIONS INVOLVING PHYSICAL EXERCISE

In the investigation of the effects of exercise upon breathing rate, pulse rate, body temperature etc., pupils should not be allowed to take part if they are not permitted to undertake ordinary school P.E activities.

When using spirometers for gas analysis, be aware of the possible consequences of hyperventilation or of holding the breath. If the experiment requires a supply of oxygen it must be of medical quality.
Warranty Period
1 Year
Notes
1. Soda lime crystals are not supplied.

2. A Kymograph or Datalogger system is required to record results. Recommended data loggers and sources:

Logit, from Breckland Scientific Supplies http://www.brecklandscientific.co.uk

Logit, from Griffin Education http://www.griffinandgeorge.co.uk

Data Harvest http://www.dataharvest.co.uk ask for data sheet DS120(1) from Data Harvest for setting up with Motion sensors.Scientific and Chemical http://www.sci-chem.co.uk

Data Harvest from Timstar http://www.timstar.co.uk ask for data sheet DS120(1)from Data Harvest for setting up with Motion sensors.

Philip Harris Aquire Data Logger with angular sensor. http://www.philipharris.co.uk/secondary/data-logging/

A pen arm is supplied to attach to the float with motion sensors/data loggers in mind.

3. Medical Grade oxygen cylinder is also required, recommend BOC Medical Tel: 0800 111 333 email: bocmedical@uk.gases.boc.com.

4. Useful flash presentation on the operation of a Spirometer http://www.mdl.cuhk.edu.hk/mdlcal/spirept7.sw

Disposable Filtered Breathing mouth piece

1. This filter prevents small particulate matter or micro-organisms from entering the body.

2. Mechanical pleated filters carry hydrophobic properties which provide a complete barrier to viral pathogens under normal conditions.